RedMax SRTZ2500 Dokumentacja

OWNER/OPERATOR MANUALSHORT REACH TRIMMERT3075-93110(204)SRTZ2500The engine exhaust from this productcontains chemicals known to the Stateof Californi

❲10❳ BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area in

Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting attachm

❲12❳• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you ar

5. For safe operation HANDLING FUEL1. The engine of the RedMax product is designedto run on a mixed fuel which contains highlyflammable gasoline. Nev

❲14❳ MOUNTING ENGINE (SE1)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft is engaged with t

6. Set upSE4 ATTACHING THE TRIMMING MECHANISM (SE4)1. Remove the cap on the end of the main pipe.2. Remove the screw screwed into the end of thetrimmi

❲16❳• Gasoline is very flammable. Avoid smokingor bringing any flame or sparks near fuel.Make sure to stop the engine and allow itcool before refueli

container to avoid mixing up with gasoline orother containers.6. Indicate the contents on outside of container foreasy identification. FUELING THE U

❲18❳ STARTING ENGINEThe cutting head will start rotating upon theengine starts.1. Rest the unit on a flat, firm place. Keep thecutting head off the g

8. Operation STOPPING ENGINE (OP3)1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP position

INFORMATION This machine is equipped with an Overload CancellationMechanism. When the cutting blades have got into metal wires or thosetwigs difficult

❲20❳handling can cause accidents which may inturn lead to serious injury or death. For thisreason, you should always be careful to followthe followin

9. Maintenance BLADES (MA1)• When refilling the tank or resting, it is often agood idea to use the time to oil the cuttingblades.• If a gap exists be

❲22❳QUICK TIPIf the blades become so worn down that it is nolonger possible to eliminate the gap between them,you should contact the authorized RedMax

SPARK PLUG• Starting failure and mis-firing are often causedby a fouled spark plug. Clean the spark plug andcheck that the plug gap is in the correc

❲24❳9. Maintenance INTAKE AIR COOLING VENT• Never touch the cylinder, muffler, or sparkplugs with your bare hands immediately afterstopping the engin

10. Storage• Aged fuel is one of major causes of enginestarting failure. Before storing the unit, empty thefuel tank and run the engine until it uses

❲26❳11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filt

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

12. Parts list ❲28❳Fig.1 DRIVE UNIT SRTZ2500 (S/N 000000 and up)Fig.2 CUTTING UNIT SRTZ2500 (S/N 000000 and up)

Fig.2 CUTTING UNIT SRTZ2500 (S/N 000000 and up)Fig.1 DRIVE UNIT SRTZ2500 (S/N 000000 and up)Key# Description Part Number Q'ty1 PIPE-COMP T3075-

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

Fig.3 ENGINE UNIT SRTZ2500 (S/N 000479 and up)❲30❳12. Parts list

Fig.3 ENGINE UNIT SRTZ2500 (S/N 000479 and up)❲31❳Key# Description Part Number Q'ty1 CYLINDER 4810-12111 12 GASKET, base 4810-12210 13 BOLT 1850

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road

KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGIN

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093© Printed in Japan

1. Parts location1. Loop handle2. Shoulder strap hanger3. Ignition switch4. Throttle cable5. Throttle lever6. Throttle set button7. Drive shaft housin

2. Specifications SRTZ2500Overall size(LxWxH)························································ 67.9(1725)x9.8(250)x12.2(310) in(mm)Dry weight

❲6❳(1) Read owner's manual before operatingthis machine.(2) Wear head, eye and ear protection.(3)Handling this machine improperlycould result in

❲7❳For safe operation and maintenance, symbols arecarved in relief on the machine. According to theseindications, please be careful not to take a mist

❲8❳5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this man

b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of th