RedMax EXZ2401S-BC Dokumentacja

OWNER/OPERATOR MANUALEXtreme™848-J8P-93A0 (603)The engine exhaust from this productcontains chemicals known to the Stateof California to cause cancer,

 10 Make sure the throttle is at idle position.Never place the throttle into the high speedposition or half throttle position (throttle lockposition

• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you are ap

 12 5. For safe operationrefill the tank of the unit in any place where thereis a boiler, stove, wood fire, electrical sparks,welding sparks, or any

MOUNTING ENGINE (SE1)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft is engaged with the g

 14 6. Set up (EX2-BC only)EX2-BCSE2 INSTALLING DEBRIS GUARD• Put the debris guard on the gear box, attach itwith the 2 screws and hardware provide

6. Set up (EX-LRT only)EX-LRTSE1 ATTACHING THE TRIMMING MECHANISM (SE1)1. Remove the screw screwed into the end of thetrimming mechanism.2. Insert the

 16 6. Set up (EX-PS only)(1)(2)(3)(4)(5)EX-PSSE1EX-PSSE2EX-PSSE3 ATTACHING THE PRUNING MECHANISM (SE1)1. Remove the cap on the end of the main pipe

6. Set up (EX-PS only)3. Fit the chain tensioner nut into the lower hole ofthe guide bar, then install the chain cover, andfasten the mounting nut to

 18 6. Set up (EX-HE only)EX-HESE1EX-HESE2EX-HESE3EX-HESE41. Insert the driveshaft into the clutch drum, thenattach the gearbox to the shaft tube as

7. Fuel and chain oil RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1(when using ZENOAH genuine oil)• Exhaust emission are controlled by thefundamental en

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

 20 7. Fuel and chain oilagain for at least one minute. As someoils may be difficult to agitate dependingon oil ingredients, sufficient agitation is

(EX-HE only) STARTING ENGINEThe RedMax stick edger is designed for edginglawn in gardens, parks, roadsides and so on. Before starting the engine, tak

 22 8. Operationlever is in to the “start” position. (OP6)6. While holding the unit firmly, pull out the starterrope quickly until engine fires. (OP

• Except for an emergency, avoid stopping theengine while pulling the throttle lever. ADJUSTING THROTTLE CABLE• The normal play is 1 or 2mm when meas

 24 8. Operation (EX2-BC only)EX2-BCOP1 CUTTING WORK (LINE HEAD USAGE)1. Always wear eye protection such as safetygoggles. Never lean over the rota

Under growthHeavy weedsLight weedsGrassNylon line headCUTTER APPLICATIONCHART9” 22-tooth:SST2299” 24-tooth:SST2498” 8-tooth:SGB0889” 8-tooth:SGB0898”

 26 8. Operation (Optional blade usage EX2-BC only)Change the loop handle to the J-handle for safeoperation. (OP4)(1) Bracket: 3583-14101(2) J-handl

8. Operation (Optional blade usage EX2-BC only) OPERATION1. Check the bolt to fasten the blade and be surethe bolt has no fault, and no abrasion.2. B

 28 2.How you can reduce the chance of blade thrust:a. Recognize that blade thrust can happen. Byunderstanding and knowing about bounce,you can help

8. Operation (Optional blade usage EX2-BC only)EX2-BCOP9 MAINTENANCEBLADE• Check the blade and the fasteners forlooseness, cracking, or bending.• Che

1. Parts locationEX2-BCEX-PSEX-LRTEX-HE12345678910111213141516171819202122232425261. Loop handle2. Shoulder strap hanger3. Ignition switch4. Throttle

 30 8. Operation (EX-LRT only)This product is equipped with extremely sharpblades, and when used improperly these bladescan be extremely dangerous,

EX-PSOP1EX-PSOP2 CHECKING OIL SUPPLY After starting the engine, run the chain at mediumspeed and see if chain oil is scattered off as shownin the fig

 32 8. Operation (EX-PS only)The oil flow adjusting screw must be pressed inslightly in order to turn. Failure to do so coulddamage the pump and scr

EX-HEOP18. Operation (EX-HE only)• Always wear eye protection such as safetygoggles. Never lean over the rotating cuttinghead. Rocks or other debris c

 34 9. Maintenanceevery every every25 50 100system/compornent procedure before hours hours hours noteuse after after afterfuel leaks, fuel spillage

•Make sure that the engine has stopped and iscool before performing any service to themachine. Contact with moving cutting heador hot muffler may resu

 36  MUFFLER• Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If any signof exhaust leakage is found, stop using the

9. Maintenancebrushcutter. Note that it is necessary to removethe engine cover shown in (MA5) in order to beable to view the upper part of the cylinde

 38 9. Maintenance (EX2-BC only)EX2-BCMA1 REFILLING TRIMMING LINE (MA1)1. For replacement line, use a diameter of .095in(2.4mm). The spool is capab

9. Maintenance (EX-LRT only) BLADES (MA1)•When refilling the tank or resting, it is often agood idea to use the time to oil the cuttingblades.• If a

 4 2. SpecificationsEngine Type······················································································ Air-cooled 2-stroke gasolineMo

 40 9. Maintenance (EX-PS only)(1)EX-PSMA1EX-PSMA2EX-PSMA3 OILING PORT Dismount the guide bar and check the oiling portfor clogging. (MA1)(1) Oilin

9. Maintenance (EX-PS only)The bar rail should always be a square. Check forwear of the bar rail. Apply a ruler to the bar and theoutside of a cutter.

 42 9. Maintenance (EX-PS only)After every cutter has been set, check the depthgauge and file it to the proper level as illustrated.(MA7) Be sure to

9. Maintenance (EX-HE only) GEAR CASE• The reduction gears are lubricated bymultipurpose, lithium-based grease in the gearcase. At every 20 hours of

11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filter ➞

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

12. Parts list  46 Fig.1 EXZ-PU (S/N 60300000 and up)

Key# Description Part Number Q'ty1PIPE COMP., ø24x750848-J8P-5820 12 SHAFT, 786x7 T3075-12210 13 SPACER 6036-12250 14 JOINT, PIPE-ASS’Y T3087-124

12. Parts list  48 Fig.2 EX2-BC (S/N 50200000 and up)

Key# Description Part Number Q'ty1 GEARCASE ASSY T3195-31001 12• GEARCASE 848-B20-62A0 13• BEARING 06004-06000 14• BEARING 06000-00626 15• RING 0

(1) Read owner's manual before operating this machine.(2) Wear head, eye and ear protection.(3) Warning/Attention(4) Keep all children, bystander

Fig.3 ENGINE UNIT (60100000 and up) 50 12. Parts list

 51 Key# Description Part Number Q'ty1 CYLINDER COMP. 848-F08-1210 12• COVER, TR-S 848-F08-12C0 13• COVER, TR-F 848-F08-12D0 14• GASKET, TR 848

12. Parts list  52 Fig.4 EX-LRT (S/N 000531 and up)

Key# Description Part Number Q'ty1 LEVER, clamp 6598-13110 12 WASHER M6 0290-20615 13 WASHER 6x15x2.0 6782-13650 14 ANGLE ADJUSTER 6782-13141 15

12. Parts list  54 Fig.5 EX-PS (S/N 000000 and up)

Key# Description Part Number Q'ty1 GEAR CASE (L)COMP. 848-A52-6211 12• BEARING 06004-06001 13 GEAR CASE (R)COMP. T3073-13200 14• BEARING 06002-00

12. Parts list  56 Fig.6 EX-HE (S/N 000101 and up)

Key# Description Part Number Q'ty1 GEARCASE ASSY 6367-13000 12• GEARCASE 6367-13110 13• O-RING 6367-13150 14• BEARING 06000-06201 15• SEAL 3180-1

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMa

 6 For safe operation and maintenance, symbols arecarved in relief on the machine. According to theseindications, please be careful not to make amis

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this manual

b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of th

 9  BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area i