RedMax PSZ2500 Dokumentacja

OWNER/OPERATOR MANUALPOLE SAWT3073-93110 (004)PSZ2500The engine exhaust from this productcontains chemicals known to the Stateof California to cause

❲10❳Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting att

• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you are ap

❲12❳5. For safe operation HANDLING FUEL1. The engine of the RedMax product is designedto run on a mixed fuel which contains highlyflammable gasoline.

KICKBACK AND PINCHING SAFETYPRECAUTIONS Beware of kickback! Kickback can occur whenever the tip of the guidebar touches an object while the saw is o

• Make sure the chain and sprocket are correctlyadjusted before operating the pruner (see page16,17 for adjustment procedures). Never attemptchain adj

MOUNTING ENGINE (SE1)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft is engaged with the g

6. Set up❲16❳A standard package contains the items as shownbelow. (SE4) (1) Guide bar (2) Saw chain (3) Gase case (4) Sprocket (5) Chain tension adjus

6. Set up❲17❳5. Tighten the mounting nut securely with thebar tip held up (SE8)(TORQUE: 8.9~11.7N.m./90~120 kg-cm). Then check thechain for smooth rot

• Gasoline is very flammable. Avoid smokingor bringing any flame or sparks near fuel.Make sure to stop the engine and allow itcool before refueling t

container to avoid mixing up with gasoline orother containers.6. Indicate the contents on outside of container foreasy identification. FUELING THE U

❲20❳ STARTING ENGINEThe cutting head will start rotating upon theengine starts.1. Feed fuel and chain oil into their respectivetanks and tighten the

8. Operation STOPPING ENGINE (OP4)1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP position

Adjust the pump as follows: 1. Stop the engine and make sure the stop switchis in the OFF position. 2. Place the unit on its side with the oil reservo

❲23❳9. Maintenance(1)MA1MA2MA3every every every25 50 100system/compornent procedure before hours hours hours noteuse after after afterfuel leaks, fuel

9. MaintenanceThe bar rail should always be a square.Check for wear of the bar rail. Apply a rulerto the bar and the outside of a cutter. If agap is o

9. MaintenanceMA8MA7Place your file on the cutter and push straightforward. Keep the file position as illustrated. (MA6) After every cutter has been s

❲26❳ GEAR CASE The reduction gears are lubricated bymultipurpose, lithium-based grease in thegearcase. Supply new grease every 25 hours of use or mor

SPARK PLUG• Starting failure and mis-firing are often causedby a fouled spark plug. Clean the spark plug andcheck that the plug gap is in the correc

❲28❳9. Maintenance INTAKE AIR COOLING VENT• Never touch the cylinder, muffler, or sparkplugs with your bare hands immediately afterstopping the engin

❲29❳10. Storage• Aged fuel is one of major causes of enginestarting failure. Before storing the unit, empty thefuel tank and run the engine until it u

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

❲30❳11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filt

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

12. Parts list ❲32❳Fig.1 DRIVE UNIT PSZ2500 (S/N 000000 and up)Fig.2 CUTTING UNIT PSZ2500 (S/N 000000 and up)

Fig.2 CUTTING UNIT PSZ2500 (S/N 000000 and up)Fig.1 DRIVE UNIT PSZ2500 (S/N 000000 and up)Key# Description Part Number Q'ty1 PIPE-COMP T3002-12

Fig.3 ENGINE UNIT PSZ2500 (S/N 000479 and up)❲34❳12. Parts list

Fig.3 ENGINE UNIT PSZ2500 (S/N 000479 and up)❲35❳Key# Description Part Number Q'ty1 CYLINDER 4810-12111 12 GASKET, base 4810-12210 13 BOLT 1850-

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL PSZ2500, UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), TH

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

2. Specifications PSZ2500Overall size(LxWxH)························································ 83.9(2130)x9.8(250)x12.2(310) in(mm)Dry weight w

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093© Printed in Japan

(1) Read owner's manual before operatingthis machine.(2) Wear head, eye and ear protection.(3) Handling this machine improperly couldresult in ac

❲6❳For safe operation and maintenance, symbols arecarved in relief on the machine. According to theseindications, please be careful not to take a mist

❲7❳5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this man

❲8❳b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of

BEFORE STARTING THE ENGINE1. Make sure there is always good ventilation whenoperating the pruner. Fumes from engineexhaust can cause serious injury