OWNER/OPERATOR MANUALCHAINSAWST2108-93110 (606)The engine exhaust from this productcontains chemicals known to the Stateof California to cause cancer,
6. Fuel and Chain oil 10 RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1(when using ZENOAH genuine oil)• Exhaust emission are controlled by thefundamen
6. Fuel and Chain oil 11 CHAIN OIL Use motor oil SAE 10W-30 all year round, orSAE 30-40 in summer and SAE 20 in winter. Do not use waste or regene
12 It is very dangerous to run a chainsaw thatmounts broken parts or lacks any parts.Before starting engine, make sure that all theparts including
Keep clear of the saw chain as it will startrotatIng upon starting of engine. CHECKING OIL SUPPLY Make sure to set up the bar and the chain whenchec
14 CHAIN BRAKE This machine is equipped with an automatic braketo stop saw chain rotation upon occurrence ofkickback while in saw cutting operati
7. Operation STOPPING ENGINE 1. Release the throttle lever to allow the engineidling for a few minutes 2. Put the switch to the "O" (STOP)
16 7. Operation HOW TO SWITCH BETWEEN OPERATINGMODES (F19)1. Flip the engine switch to turn off the engine.2. Remove the cover to the air filter,
• Before proceeding to your job, read "ForSafe Operation" section It is recommendedto first practice sawing easy logs. This alsohelps you ge
18 FELLING A TREE (F22) 1. Decide the felling direction considering thewind, lean of the tree, location of heavybranches, ease of job after felli
A Log lying on the ground (F23) Saw down halfway, then roll the log over and cutfrom the opposite side. A Log hanging off the ground (F24) In area A,
20 9. MaintenanceMaintenance, replacement, or repair of theemission control device and systems may beperformed by any non-road engine repairestabli
9. Maintenance4. Others Check for fuel leakage and loose fastenings anddamage to major parts, especially handle jointsand guide bar mounting. If any d
22 4. Spark plug (F34) Clean the electrodes with a wire brush and resetthe gap to 0.65 mm as necessary.ChampionRCJ-7Y 5. Sprocket (F35) Check for c
SAW CHAIN It is very important for smooth and safeoperation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust beco
24 10. Maintenance of Saw Chain and Guide Bar Make sure every cutter has the same length andedge angles as illustrated. (F38) (4) Cutter length (5)
11. Troubleshooting GuideCase 1. Starting failure: Make sure the icing prevention system is not working. Case 2. Lack of power/Poor acceleration/Rough
26 1. Empty the fuel tank and run the engine out offuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of t
27 13. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does no
28 G3800AVS13. Parts list Fig.1 POWER UNIT (S/N 001881 and up)
29 G3800AVSFig.1 POWER UNIT (S/N 001881 and up)Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE51 848-C40-5121 Clutch ass’y 152 2870-51230 • Spring 1
SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to
G3800AVS13. Parts list Fig.2 POWER UNIT (S/N 001881 and up) 30
G3800AVSFig.2 POWER UNIT (S/N 001881 and up)Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE50 2872-54230 • Spring 151 2851-54260 • Stopper plate 152 28
Fig.3 CARBBURETOR COMPONENTS (S/N 001881 and up)Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE17 –––––––––– • • SCREEN –18 –––––––––– • • VALVE, inlet
33 G3800AVSFig.4 ACCESSORIES (S/N 001881 and up)Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE Key# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE1 3320
KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINA
KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 Pièces en rapport avec les émissions de gaz d'échappement : R
KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093
2. Specifications G3800AVSPower unit : Dis placement ··················································································· 2.34(37.2)
3. Symbols on the machine 5 Made in JapanRedMax IMPORTANT ENGINE INFORMATION THIS ENGINE CONFORMS TO US EPA PH1 FOR SMALL OFF-ROAD ENGINES.
6 4. For safe operation1. Never operate a chain saw when you arefatigued, ill, or upset, or under theinfluence of medication that may makeyou drows
7 4. For safe operation16. Operate the chain saw only in wellventilated areas. Never start or run theengine inside a closed room or building.Exhaus
A standard saw unit package contains the items asillustrated. (F1) (1) Power unit (2) Guide bar (3) Saw chain (4) Plug wrench (5) Screwdriver for carb
5. Installing guide bar and saw chain 9 7. Tighten the tensioner screw. (2) Loosen (3) Tighten (4) Tensioner screw A new chain will expand its lengt
Komentarze do niniejszej Instrukcji