RedMax BT250 Dokumentacja Strona 1

OWNER/OPERATOR MANUALLINE TRIMMERBT25-00000 (404)The engine exhaust from this productcontains chemicals known to the Stateof California to cause cance

 10 Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting a

• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you are ap

 12 5. For safe operationrefill the tank of the unit in any place where thereis a boiler, stove, wood fire, electrical sparks,welding sparks, or any

INSTALLING HANDLE (SE1)•Mount the handle to the shaft tube and clamp itat your best operating position. INSTALLING DEBRIS GUARD (SE2)• Put the debr

 14 7. Fuel RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1• Exhaust emission are controlled by thefundamental engine parameters andcomponents(eq., carbu

7. Fuel 15 again for at least one minute. As someoils may be difficult to agitate dependingon oil ingredients, sufficient agitation isnecessary for

 16  STARTING ENGINEThe cutting head will start rotating upon theengine starts.1. Rest the unit on a flat, firm place. Keep thecutting head off the

8. Operation STOPPING ENGINE1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP position.• Exc

 18 3. Use a slow, deliberate action to cut heavygrowth. The rate of cutting motion will depend onthe material being cut. Heavy growth will requires

9. MaintenanceMaintenance, replacement, or repair of the emission control device and systems may beperformed by any non-road engine repair establishme

 20 9. Maintenance8 11 1412910 121315THISSIDE UPTHISSIDE UPWINDLINE

•Make sure that the engine has stopped and iscool before performing any service to thebrushcutter. Contact with moving cuttinghead or hot muffler may

 22  MUFFLER•Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If anysign of exhaust leakage is found, do not usethe b

9. Maintenancehours of use for blockage, and remove anywaste which has attached itself to thebrushcutter. Note that it is necessary to removethe plug

 24 11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel fi

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

12. Parts list  26 Fig.1 DRIVE UNIT BT250 (S/N 40400101 and up)

Fig.1 DRIVE UNIT BT250 (S/N 40400101 and up) 27 Key# Part Number Description Q'ty1 BT25-50810 PIPE COMP. 12 BT25-50710 DRIVE SHAFT 13 BT25-509

Fig.2 ENGINE UNIT BT250 (S/N KU40001 and up) 28 12. Parts list

Fig.2 ENGINE UNIT BT250 (S/N KU40001 and up) 29 Key# Part Number Description Q'ty1 6634401 SCREW 42 3075406 FRONT HOUSING 13 6635301 SCREW CLU

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMa

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

2. Specifications BT250Overall size(LxWxH)······················································ 63.0(1600)x13.0(330)x12.0(305) in(mm)Dry weight w/o

(1) Read owner's manual before operating this machine.(2) Wear head, eye and ear protection.(3) Warning/Attention(4) Keep all children, bystander

 6 For safe operation and maintenance,symbols are carved in relief on the machine.According to these indications, please becareful not to make a mis

 7 5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this m

 8 b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview

BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area into w